« Back to Catalogue

Powersoft M50Q Dsp Ethernet

€50/1-3days €100/week €300/month

Powersoft M50Q Dsp Ethernet Image

Amplificatore 4 ch con DSP interno dedicato ai monitor wedge Edge 15 biamplificati

Numero canali 4
Potenza d’uscita Single channel mode Distributed line* Bridge mode
  4 Ω 8 Ω   70V 100V   8 Ω    
1250 W 750 W 1000 W 1250 W 2500W
Tensione massima / corrente di picco 135 Vpeak / 65 Apeak 270 Vpeak
Alimentazione CA
Alimentazione Universal, regulated switch mode
Tensione operativa 100-240 V ±10%, 50-60 Hz
Tensione di funzionamento 90 V – 264 V
Consumo energetico** 115 V 230 V
Idle 64 W 0.6 A 64 W 0.51 A
1/8 potenza massima @ 4 Ω 905 W 11.6 A 905 W 5.8 A
1/4 potenza massima @ 4 Ω 1772 W 22.2 A 1772 W 11.1 A
Caratteristiche termiche
Range di temperatura operativa 0° – 45° C – 32° – 113° F
Dissipazione termica** 115 V 230 V
Idle 218 BTU/h 54.9 kcal/h 218 BTU/h 54.9 kcal/h
1/8 potenza massima @ 4 Ω 955 BTU/h 240.7 kcal/h 955 BTU/h 240.7 kcal/h
1/4 potenza massima @ 4 Ω 1781 BTU/h 448.8 kcal/h 1781 BTU/h 448.8 kcal/h
Audio
Guadagno 32dB, 30dB, 28dB, 26dB, 24dB, 22dB, 20dB, 18dB, 14dB, 4dB, -∞, user selectable
Sensibilità d’ingresso 1.94 V / 8 dBu
Livello massimo di ingresso 6 V / 17.8 dBu
Risposta in frequenza 20 Hz – 20 kHz (±0.5 dB) @ 1 W, 8 Ω
Rapporto segnale/rumore > 110 dB (20 Hz – 20 kHz, A weighted)
Separazione Crosstalk > 70 dB @ 1kHz
THD+N < 0.05% @ 1/2 full power
IMD < 0.02%
Impedenza d’ingresso 10 kΩ balanced
Slew rate 50 V/μs @ 8Ω, input filter bypassed
Fattore di smorzamento > 5000 @ 100 Hz
DSP
Architettura DSP Analog Devices ADAU® 1701 DSP
Convertitore A/D Cirrus Logic CS 5381, 2 channel, 24 bit @ 48 kHz, 120 dB S/N
Convertitore D/A Cirrus Logic CS 4398, 2 channel, 24 bit @ 48 kHz, 120 dB S/N
Precisione interna Fixed point
Firmware Network upgradable firmware
Latenza 0.644 ms fixed latency architecture
Equalizzatore ingresso up to 5 biquad IIR filters (PEQ, shelving, band pass, band stop, all pass)
Equalizzatore uscita up to 12 fully parametric per channel
Crossover Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct
Delay 340 ms input delay plus 10 ms per output
Limiters Peak limiter, RMS limiter, frequency dependent RMS limiter
Controllo di smorzamento < 120 Hz, range ±2 Ω
Pannello anteriore
Indicatori e comandi 2 x LED – Status
2 x LED – Over-temperature protection
4 x LED bar – Signal level and over-temperature protection
4 x Knob – Level attenuator (stepped)
1 x Power switch –
Connettori
AC main 1 x IEC C14 connector – 15 A max (region-specific power cord provided)
Audio signal input 4 x XLR – Signal input
Auxiliary voltage 1 x 2 pin Phoenix MC 1.5/2-ST-3.81 – External voltage connector (DSP version only)
Loudspeakers 4 x speakON – Neutrik NL4MD
Network/data 1 x Rj45 socket – RS485 data connection (non-DSP version)
Pannello posteriore
Indicatori e comandi 1 x Push-button – Link channel pair
Costruzione
Dimensioni (L x H x P) 483 mm x 44.45 mm x 358 mm (19.0 in x 1.8 in x 14.1 in)
Peso 7.4 kg
« Back to Catalogue

Powersoft M50Q Dsp Ethernet

€50/1-3days €100/week €300/month

Powersoft M50Q Dsp Ethernet Image

Amplificatore 4 ch con DSP interno dedicato ai monitor wedge Edge 15 biamplificati

Numero canali 4
Potenza d’uscita Single channel mode Distributed line* Bridge mode
  4 Ω 8 Ω   70V 100V   8 Ω    
1250 W 750 W 1000 W 1250 W 2500W
Tensione massima / corrente di picco 135 Vpeak / 65 Apeak 270 Vpeak
Alimentazione CA
Alimentazione Universal, regulated switch mode
Tensione operativa 100-240 V ±10%, 50-60 Hz
Tensione di funzionamento 90 V – 264 V
Consumo energetico** 115 V 230 V
Idle 64 W 0.6 A 64 W 0.51 A
1/8 potenza massima @ 4 Ω 905 W 11.6 A 905 W 5.8 A
1/4 potenza massima @ 4 Ω 1772 W 22.2 A 1772 W 11.1 A
Caratteristiche termiche
Range di temperatura operativa 0° – 45° C – 32° – 113° F
Dissipazione termica** 115 V 230 V
Idle 218 BTU/h 54.9 kcal/h 218 BTU/h 54.9 kcal/h
1/8 potenza massima @ 4 Ω 955 BTU/h 240.7 kcal/h 955 BTU/h 240.7 kcal/h
1/4 potenza massima @ 4 Ω 1781 BTU/h 448.8 kcal/h 1781 BTU/h 448.8 kcal/h
Audio
Guadagno 32dB, 30dB, 28dB, 26dB, 24dB, 22dB, 20dB, 18dB, 14dB, 4dB, -∞, user selectable
Sensibilità d’ingresso 1.94 V / 8 dBu
Livello massimo di ingresso 6 V / 17.8 dBu
Risposta in frequenza 20 Hz – 20 kHz (±0.5 dB) @ 1 W, 8 Ω
Rapporto segnale/rumore > 110 dB (20 Hz – 20 kHz, A weighted)
Separazione Crosstalk > 70 dB @ 1kHz
THD+N < 0.05% @ 1/2 full power
IMD < 0.02%
Impedenza d’ingresso 10 kΩ balanced
Slew rate 50 V/μs @ 8Ω, input filter bypassed
Fattore di smorzamento > 5000 @ 100 Hz
DSP
Architettura DSP Analog Devices ADAU® 1701 DSP
Convertitore A/D Cirrus Logic CS 5381, 2 channel, 24 bit @ 48 kHz, 120 dB S/N
Convertitore D/A Cirrus Logic CS 4398, 2 channel, 24 bit @ 48 kHz, 120 dB S/N
Precisione interna Fixed point
Firmware Network upgradable firmware
Latenza 0.644 ms fixed latency architecture
Equalizzatore ingresso up to 5 biquad IIR filters (PEQ, shelving, band pass, band stop, all pass)
Equalizzatore uscita up to 12 fully parametric per channel
Crossover Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct
Delay 340 ms input delay plus 10 ms per output
Limiters Peak limiter, RMS limiter, frequency dependent RMS limiter
Controllo di smorzamento < 120 Hz, range ±2 Ω
Pannello anteriore
Indicatori e comandi 2 x LED – Status
2 x LED – Over-temperature protection
4 x LED bar – Signal level and over-temperature protection
4 x Knob – Level attenuator (stepped)
1 x Power switch –
Connettori
AC main 1 x IEC C14 connector – 15 A max (region-specific power cord provided)
Audio signal input 4 x XLR – Signal input
Auxiliary voltage 1 x 2 pin Phoenix MC 1.5/2-ST-3.81 – External voltage connector (DSP version only)
Loudspeakers 4 x speakON – Neutrik NL4MD
Network/data 1 x Rj45 socket – RS485 data connection (non-DSP version)
Pannello posteriore
Indicatori e comandi 1 x Push-button – Link channel pair
Costruzione
Dimensioni (L x H x P) 483 mm x 44.45 mm x 358 mm (19.0 in x 1.8 in x 14.1 in)
Peso 7.4 kg